1、水系統：為避免未通水或水壓過低，加裝水壓檢測，水壓未達到使 用要求，設備無法運行并報警提示； 2、壓力安全保障：設定充氣壓力，排氣上下限，通過控制合理充氣壓 力，壓力達到排氣上限自動泄壓來保障安全，并加裝機械式安全閥作 為第二道安全保障，極大的保障設備安全； 3、一鍵啟動系統：未避免操機人員對設備了解不夠造成誤操作，我們 設置好一鍵啟動系統，用戶只需設定好熱處理回火工藝，打開自動啟 1. Water system: in order to avoid the failure of water flflow or low water pressure, add  water pressure detection, water pressure does not meet the requirements of use,  equipment can not operate and alarm; 2, pressure safety guarantee: set the inflflation pressure, exhaust upper and lower  limits, by controlling the reasonable inflflation pressure, pressure reaches the exhaust  upper limit automatic pressure relief to ensure safety, and install mechanical safety  valve as the second safety guarantee, greatly ensure the safety of equipment; 3, a key launch system: not prevent the fuck machine technician to understand  enough equipment cause wrong operation, we set up a key launch system, the users  only need to set a good tempering heat treatment process, open the automatic start  button, the equipment is automatic, nitrogen fifilling, heating, vacuum pressure relief  automatically after open fan until the end of the process, as far as possible to reduce  the operating quality of the machine; 4. Interlock: vacuumization and heating, running fan, charging, exhaust, etc. can not  be carried out at the same time, and the heating in vacuum state affffects the uniformity of furnace temperature; The motor coil is burned out when the fan is running under  vacuum condition. When vacuumizing, turn on the gas and exhaust, resulting in  vacuumization failure or failure to meet the set vacuum requirements, etc. Interlocking function can avoid these risks. 控制系統 爐外溫控系統采用日本進口島電智能數顯溫度控制器，通過對其合理參數設定，可以達到加熱溫區最佳控制，利用其在線自整定功能，能計算出 爐子的最佳 PID 參數，達到較為理想的溫度穩定性。內控溫度為 10 寸液晶顯示觸摸屏，自動顯示記錄工藝流程曲線，機械動作及控溫可以在觸 摸屏上操作，操作方便。簡單。根據客戶需求，一爐多用，整臺設備控制分為自動和手動，可以設置一鍵啟動，也可以手動開啟任意一個機械動作， 靈活操作。 1.1 控溫儀表 Control system The temperature control system of the furnace adopts the intelligent digital temperature controller imported from Japan, which can achieve the best control of the heating  temperature area by setting reasonable parameters. The optimal PID parameters of the furnace can be calculated by using its online self-tuning function, so as to achieve the  ideal temperature stability. Internal temperature control for 10 inch LCD touch screen, automatic display record process curve, mechanical action and temperature control can be  operated on the touch screen, easy to operate. Simple. According to customer demand, one furnace multi-purpose, the whole equipment control is divided into automatic and  manual, can set a key to start, can also manually open any mechanical action, flflexible operation. 1.1 Temperature controller table 動按鈕，設備即自動抽真空、充氮?dú)?、加熱、開啟風機直至工藝結束后 自動泄壓，盡可能降低對操機人員的素質要求； 4、互鎖：程序設定抽真空與加熱、運行風機、充氣、排氣、等均不可同 時進行，真空狀態加熱影響爐溫均勻性；抽真空狀態運行風機導致電 機線圈燒壞；抽真空時，打開充氣、排氣，導致無法抽真空或者達不到 設定真空要求等問題，通過互鎖功能，可規避這些風險。